1. 

전기용량

 Watts :   Volts :   Phase :

플랜지이머젼히터의 Immersion길이

 "B" 길이:         ; mm
 비발열부 길이:  mm

2. 

각 플랜지에 따른 히터의 수량

3"/3 6"/12 8"/18 10"/27 12"/36 
14"/45 16"/72 18"/108 Other

3. 

플랜지 및 베셀 재질

Carbon Steel Carbon Steel-Galvanized
304 Stainless Steel Other  

4.

CIRCULATION HEATER의 사이즈

 A : mm    B : mm    D : mm  
 F : mm    C : mm    E : mm

5. 

FLANGE 규격

Class 150 Class 300 Other  

6. 

HEATING ELEMENT SHEATH 재질

Copper 304 Stainless Steel INCOLOY
316 Stainless Steel Other  

7. 

HEATING ELEMENT WATT DENSITY [W/In² ]

6.5 15 23 45 Other  

8. 

TERMINAL SEALS:

Yes No Silicone Fluid (500°F)
Silicone Resin(450°F) RTV (450°F
Epoxy(250°F) Other

9. 

단자박스 구조

 TYPE 1  TYPE  2  TYPE 3  TYPE 4

10. 

TERMINAL ENCLOSURE STANDOFFS

Yes No 4" 6" Other  

11. 

가스켓 재질[FLANGE GASKET]

Standard Spiral Wound  Other

12. 

자체성적서 필요여부

필요 필요엾음   기타

13. 

ELECTRICAL CODES:

UL Listed CSA Certified
National Electrical Code Other  

14. 

보온재[THERMAL INSULATION]

None Standard High Temperature
Weatherproof Jacket

15. 

CIRCULATION

No Unbaffled No Baffled 

16. 

NOZZLE SIZE, TYPE AND ORIENTATION

No standard or as Indicated below:

1. Size

2. Type

 3. Rating

4.Location

5.Orientation

16.1

Size is Nominal

16.2

Type is NPT threaded or raised face Flange

16.3

Rating is 150 Lb. 300 Lb. etc. if Flanged 

16.4

Location is A, B or C (from Figure)

16.5

Orientation is 1,2,3 or 4 (from Figure)

17. 

MOUNTING POSITION:

Vertical-Terminal Box Up Down
Horizontal

18. 

MOUNTING METHOD:

Standard or as Indicated Below:
 Mounting Lugs-Orientation Number 
 Mounting Saddles-Orientation Number 
 Orientation Number is 1,2,3 or4 (from figure) 

19. 

서클레이션히터에 LIFTING LUGS설치

 설치함 설치않함

20.

플랜지히터에 LIFTING LUGS설치

설치함 설치않함

21. 

DRAIN PIPE-3/4" NPT:

Yes (Horizontal Mound) No

22. 

MECHANICAL PROCESS TEMPERATURE CONTROL MOUNTED ON HEATER :

Yes No

a)

 TYPE 1  TYPE  2  TYPE 3  TYPE 4

b)Temperature Range( F)

 0-100 60-250 200-500 300-700

23.

ELECTRONIC PROCESS TEMPERATURE CONTROL MOUNTED ON HEATER :

 Yes No

 TYPE 1  TYPE  2  TYPE 3  TYPE 4

 0 - 200 C0 - 500 C

24.

MECHANICAL PROCESS TEMPERATURE HIGH LIMIT PROTECTION CONTROL MOUNTED ON HEATER:

 Yes No

 TYPE 1  TYPE  2  TYPE 3  TYPE 4

 0-100 60-250 200-500 300-700

25.

PROCESS THERMOCOUPLE IN OUTLET:

a)Thermocouple type

 Yes No Type J Type K

b)With separate Terminal Box

 No None No General Purpose
 No Moisture Resistant Explosion Resistant 

26.

ELECTRONIC HIGH LIMIT PROTECTION CONTROL MOUNTED ON HEATER :

 Yes No

 General Purpose Moisture Resistant
 Explosion Resistant 

27.

OVERHEAT THERMOCOUPLE ON HEATING ELEMENT SHEATH :

 Yes No Type J Type K

With separate Terminal Box

 No None No General Purpose
 No Moisture Resistant Explosion Resistant 

28.

SKID MOUNTED CIRCULATION HEATER SYSTEM COMPLETE WITH CONTROL PANEL WIRED TO HEATER:

 Yes No 

 Vertical Orientation Vertical Orientation
 Control Panel (Attach Detail Requirements) 

29.

VESSEL에 SAFETY V/V 설치

 불필요    필요시 규격 및 재질 

VESSEL에 AIR VENT 설치

 불필요    필요시 규격 및 재질 

VESSEL에 DRAIN V/V설치

 불필요    필요시 규격 및 재질 

VESSEL에 PRESSURE GAUGE 설치

 불필요    필요시 규격 및 재질 

30.

기타 추가적인 사양
 

1.

사용 용도 및 사용조건 :

Heated Medium                                   : GAS  WATER   OIL  AIR   STEAM  

2.

온도 범위

 설계 온도 -  INLET : °C,  OUTLET : °C
 사용 온도 -  INLET : °C,  OUTLET : °C

3.

피가열체의 종류 및 물리적 수치

 피가열체      비중 :
 밀도 : Kg/m³,               비열 : Kcal/Kg °C

4.

유체의 유량

  m³/Hr , SCFM ,GPM  
 Lbs/Hr or Other (Specify)  

5.

 START-UP TIME

  Hr

6.

압력 범위

 설계 압력- INLET: Kg/Cm²,  OUTLET: Kg/Cm²
 사용 압력- INLET: Kg/Cm²,  OUTLET: Kg/Cm²

7.

히터 설치장소

 INDOOR          OUTDOOR

HAZARDOUS AREA ENVIRONMENT:

 Class Div Group